10 Wheel Concrete Handling Equipment 6x4 10m3 Cement Mixer Truck 336hp
Sinotruk Howo Concrete Handling Equipment 10 Wheel 6x4 10m3 Concrete Mixer Truck 336hp
Introduction of Sinotruk Howo 10 Wheel 6x4 10m3 Concrete Mixer Truck 336hp
The concrete mixer truck is mainly composed of a chassis, a mixing drum, a transmission system (driving device), a hydraulic drive system, a water filling system, a loading (in) and discharge system, a discharge chute, an operating platform, a control system, and protective equipment.
Application and characteristics:
Powerful powertrain, high power and high torque. Short wheelbase, narrow wheelbase, strong and durable chassis, high suspension capacity, high degree of versatility. Concrete mixer truck can be widely used in the construction of mines, tunnels, townships, villages, towns, highways, water conservancy projects, large-scale projects, short-term, small projects, micro-miniature mixing stations, subways, national defense and other projects.
Highlights of Sinotruk Howo 10 Wheel 6x4 10m3 Concrete Mixer Truck 336hp
Mixer: The mixer used in this model is a structure that is more commonly used. The mixer uses a pear-shaped structure. The cleaning water and the mixing water added during the transportation process as needed are fed from the mixer head. The material mouth is injected into the cylinder.
Transmission system: The driving method of the agitating cylinder is to use the engine as the power source. The power is taken by the power take-off at the rear end of the engine, and transmitted to the variable piston hydraulic pump through the transmission shaft. The barrel turns. Feeding and discharging system (loading and unloading mechanism) of the mixing drum: It is an important device to assist the working of the mixing drum.
Control system: It is the control part of the whole mixer. The control panel is provided with an "I-shaped" groove, which is the movement space of the joystick. And the slot in the rear half is provided with a limited hole for fixing the position of the joystick. The control system controls the forward, reverse and rotation speed of the mixing drum through the left and right joysticks at the rear of the car, so as to complete the feeding and discharging and stirring actions.
Water supply system: The water supply system of the concrete mixer truck is mainly used to clean the mixing device. There are two types of water supply system for this model, one is the centrifugal pump water supply system; the other is the pressure water tank water supply system, which can be installed by users.
Technical specification of Sinotruk Howo 10 Wheel 6x4 10m3 Concrete Mixer Truck 336hp
| Sinotruk Howo 10 Wheel 6x4 10m3 Concrete Mixer Truck 336hp |
| Dimension(Lx W xH)(unloaded)(mm) | 9125×2496×3850 |
| Mixer Tank Capacity(m³) | 10 |
| Approaching angle/Departure angle(°) | 16/26 |
| Overhang(front/rear) (mm) | 1500/2240 |
| Wheel base (mm) | 3625+1350 |
| Max speed(km/h) | 90 |
| Curb weight(kg) | 13000 |
| Rated Weight(kg) | 11870 |
| Engine | Model | WD615.69 |
| Fuel type | Diesel |
| Power, max(kw/rpm) | 336HP |
| Emission | EUROII |
| Fuel tanker capacity (L) | 400L |
| Transmission | HW19710 |
| Steering system | ZF8118 |
| Front axle | HF9 |
| Rear axle | HC16 |
| Tire | 12.00R20 |
| Electrical system | Battery | 2X12V/165Ah |
| Alternator | 28V-1500kw |
| Starter | 7.5Kw/24V |
| Cab | HOWO76 New face cab(one bed,with air conditioner), all-steel forward control,55ºhydraulically tiltable to the front,2- arm windscreen wiper system with three speeds, laminated windscreen with casted-in radio aerial, hydraulically damped adjustable driver’s seat and rigid adjustable co-driver’s seat, with heating and ventilating system, outer sun visor, adjustable roof flap, with stereo radio/cassette recorder, safety belts and adjustable steering wheel, air horn, with 4-point support fully floating suspension and shock absorbers. |
Maintenance method of mixer truck:
1. Change the oil
If there is a difference between winter and summer in the diesel engine manual, the summer oil should be replaced and used. The method is: make the diesel water temperature reach 80 degrees, and drain the oil while it is hot (be careful not to burn your hands). After waiting for 30 minutes, tighten the oil drain plug, add the same amount of diesel to the oil pan, and run at medium speed for 1 to 2 minutes to release the clean diesel and leave it for washing. In this way, the oil circuit can be drained and cleaned, and the oil passage is unobstructed, creating conditions for trouble-free operation of the lubricating oil circuit. Add summer oil.
2. Clean three filters and three nets
Air filters, diesel filters, oil filters are commonly known as three filters. The main points for cleaning the three filters are: ① The three filters are paper filter elements. Except for the air filter element which can be used after cleaning, the rest are replaced with new ones. ② For metal filters and filter elements, you can only clean them with clean oil, a brush or a gas cylinder, blow out the dirt with gas, and do not burn it. "Three nets" refers to the filter of the diesel fuel filler, oil filler, and exhaust gas exhaust port, which should be thoroughly cleaned to ensure unobstructed access.
3. General cleaning
Remove the insulation quilt and clean the machine. Clean up dirt, sundries, greasy dirt, and wash your face thoroughly. During the process of cleaning, clearing, and cleaning, loose nuts, rivets, and surface defects can be found, and they must be replaced and repaired in time.
4. Rotating oil indicator
For diesel engines with a "winter, summer" rotation indicator engraved in the lubricating oil circuit (usually installed at the filter), the arrow of the indicator should be rotated to point to the "summer" word to achieve a large oil circulation. In this way, the phenomenon that the oil temperature is too high and the oil pressure is reduced can be effectively avoided, thereby reducing the phenomenon of wear of the parts.
Product Tags:
|
|
10 Wheel Concrete Handling Equipment 6x4 10m3 Cement Mixer Truck 336hp Images
|
